{"id":402,"date":"2025-02-20T11:47:00","date_gmt":"2025-02-20T03:47:00","guid":{"rendered":"https:\/\/kedadhesive.com\/?p=402"},"modified":"2026-10-20T09:45:38","modified_gmt":"2026-10-20T01:45:38","slug":"marble-to-marble-bonding-expert-techniques","status":"publish","type":"post","link":"https:\/\/kedadhesive.com\/vi\/marble-to-marble-bonding-expert-techniques\/","title":{"rendered":"Marble-to-Marble Bonding: Preparation, Color and Support"},"content":{"rendered":"<p class=\"wp-block-paragraph\">A marble joint can fail visually before it fails mechanically: the edge sits proud, the seam opens at one end, or the adhesive becomes a dark line after polishing. These problems often begin with fit, preparation and positioning rather than the adhesive\u2019s advertised strength.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">For repeatable <strong>marble-to-marble bonding<\/strong>, plan the whole sequence: dry-fit the parts, select the adhesive and color, prepare both faces, mix accurately, position the pieces and maintain support through curing.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">This guide covers nonstructural workshop fabrication, decorative edges and compatible local repairs. Installed stone that carries loads, spans an opening or forms part of a wall-fixing system requires its own support and connection design.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Identify the Joint Before Choosing the Method<\/h2>\n\n\n\n<figure class=\"wp-block-table\"><table class=\"has-fixed-layout\"><thead><tr><th>Workshop task<\/th><th>Main detail to check<\/th><th>What the sample should reproduce<\/th><\/tr><\/thead><tbody><tr><td>Laminated decorative edge<\/td><td>Contact and alignment between the slab and added strip<\/td><td>Bonding faces, edge profile, joint appearance and finishing<\/td><\/tr><tr><td>Mitered edge assembly<\/td><td>Cut accuracy and the visible outside corner<\/td><td>Miter fit, positioning method and finished corner<\/td><\/tr><tr><td>Small local piece repair<\/td><td>Condition of the broken stone and completeness of the fit<\/td><td>Actual fracture faces, repair position and intended handling<\/td><\/tr><tr><td>Decorative stone detail<\/td><td>How the pieces are positioned and supported<\/td><td>Joint geometry, assembly access and final appearance<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\">Inspect the stone around the proposed joint. A loose or fractured surface layer remains a weakness even when the adhesive attaches to it. Identify existing resin, backing, wax or sealer because the adhesive may contact that treatment rather than bare marble.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">For the wider application context, see KEDA\u2019s <a href=\"https:\/\/kedadhesive.com\/vi\/solutions\/stone-fabrication-repair\/\" target=\"_blank\" rel=\"noreferrer noopener\">Stone Fabrication &amp; Repair solutions<\/a>.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Select the Adhesive for the Actual Fabrication Task<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">A knife-grade polyester paste can be relevant to compatible nonstructural edge assembly and local repair. Its consistency helps with placement, while the cured joint must suit the intended finishing process.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">An epoxy may be a different selection for a particular stone joint or installation interface. Choose by the actual product and application; a resin-family name is not a universal strength or exposure rating. Our <a href=\"https:\/\/kedadhesive.com\/vi\/understanding-marble-adhesive-composition-and-properties\/\" target=\"_blank\" rel=\"noreferrer noopener\">polyester, epoxy and cement-based adhesive comparison<\/a> explains the different roles.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">For exterior service, repeated wetting or a joint designed to move, review the appropriate material and assembly before using the workshop process below.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Step 1: Dry-Fit and Plan the Positioning<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Bring the pieces together without adhesive while both are fully supported. Check that the joint closes as intended, the exposed surfaces align and the stone pattern is oriented correctly.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">Four Useful Dry-Fit Checks<\/h3>\n\n\n\n<ul class=\"wp-block-list\">\n<li><strong>Fit:<\/strong> the faces meet without forcing a twisted or poorly cut piece into place.<\/li>\n\n\n\n<li><strong>Alignment:<\/strong> the visible edge, top surface and planned profile line up.<\/li>\n\n\n\n<li><strong>Access:<\/strong> clamps and cleanup tools can reach their working positions.<\/li>\n\n\n\n<li><strong>Sequence:<\/strong> the parts can be moved into position within a manageable assembly cycle.<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">Mark orientation outside the bonding area using a method that will not stain the stone. Rehearse the clamp placement. If the dry fit exposes a significant gap or rocking surface, correct the fit before mixing adhesive.<\/p>\n\n\n\n<figure class=\"wp-block-image aligncenter size-large\"><img fetchpriority=\"high\" decoding=\"async\" width=\"1024\" height=\"768\" src=\"https:\/\/kedadhesive.com\/wp-content\/uploads\/2025\/02\/keda-marble-bonding-dry-fit-alignment-1024x768.webp\" alt=\"Illustration of supported marble pieces being dry-fitted to check edge alignment\" class=\"wp-image-1101\" srcset=\"https:\/\/kedadhesive.com\/wp-content\/uploads\/2025\/02\/keda-marble-bonding-dry-fit-alignment-1024x768.webp 1024w, https:\/\/kedadhesive.com\/wp-content\/uploads\/2025\/02\/keda-marble-bonding-dry-fit-alignment-300x225.webp 300w, https:\/\/kedadhesive.com\/wp-content\/uploads\/2025\/02\/keda-marble-bonding-dry-fit-alignment-768x576.webp 768w, https:\/\/kedadhesive.com\/wp-content\/uploads\/2025\/02\/keda-marble-bonding-dry-fit-alignment-16x12.webp 16w, https:\/\/kedadhesive.com\/wp-content\/uploads\/2025\/02\/keda-marble-bonding-dry-fit-alignment-600x450.webp 600w, https:\/\/kedadhesive.com\/wp-content\/uploads\/2025\/02\/keda-marble-bonding-dry-fit-alignment.webp 1448w\" sizes=\"(max-width: 1024px) 100vw, 1024px\" \/><\/figure>\n\n\n\n<h2 class=\"wp-block-heading\">Step 2: Prepare Both Bonding Faces<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Remove loose particles and cutting dust, then address oil, wax and other contamination with a preparation method compatible with the stone, its treatment and the adhesive. Let the bonding faces dry before assembly.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Where the product requires abrasion, confine it to the bonding area and protect the polished finish. Collect preparation dust using suitable controls rather than leaving it on the newly prepared face. Follow the tool and product safety instructions for dust control, ventilation and protective equipment.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">Treat Coatings and Old Adhesive as Separate Issues<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">A resin-coated face, mesh backing or previously repaired surface needs assessment as that specific interface. Old material may hide weak stone or interfere with the fit. Avoid removing a treatment blindly if doing so could damage the component.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Trial the proposed preparation on a representative offcut. A fixed waiting period after washing does not establish dryness under every workshop condition, and a generic solvent recommendation does not establish compatibility with every marble finish.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Step 3: Approve the Cured Joint Color<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Choose the closest suitable base color and use a compatible tinting accessory where needed. Evaluate the color in a sample that resembles the intended joint, including its depth, width and final finish.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">For a miter, inspect the exposed corner. For a laminated edge, inspect the line after the profile is machined. A thin wet smear on a mixing board provides only an early screening check.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><a href=\"https:\/\/kedadhesive.com\/vi\/product\/stone-adhesive-color-paste\/\" target=\"_blank\" rel=\"noreferrer noopener\">KEDA Stone Adhesive Color Paste<\/a> is a related accessory for compatible adhesive systems. Our <a href=\"https:\/\/kedadhesive.com\/vi\/color-matching-adhesives-for-marble-installation-projects\/\" target=\"_blank\" rel=\"noreferrer noopener\">color-matching guide for marble adhesives<\/a> explains measured trials and sample approval.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Step 4: Measure and Mix a Manageable Batch<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Check the identity of the adhesive and matched hardener, then measure using the product\u2019s stated ratio and basis. Weight and volume ratios describe different measurements. Keep color additions and curing components separately recorded.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Use clean tools and blend thoroughly, bringing material from the sides and bottom into the mixture. Follow the specified tinting sequence. If the components have similar colors, an apparently uniform shade alone is a weak check of mixing completeness.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Prepare the dry-fitted parts, supports and tools first. Choose a batch size that fits the application and positioning window, and record material temperature when establishing the production cycle. Adding extra hardener is not a substitute for improving the assembly sequence.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Step 5: Apply the Adhesive at the Intended Interface<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Spread the mixed adhesive over the prepared bonding area using the method required for the joint. Work it into contact with the face rather than leaving an isolated mound that may trap a void or prevent the pieces from seating.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">The aim is the specified adhesive contact and bond line. More material cannot correct an unsuitable joint geometry. A deliberately large bead also does not establish adequate contact along a long edge.<\/p>\n\n\n\n<figure class=\"wp-block-image aligncenter size-large\"><img decoding=\"async\" width=\"1024\" height=\"768\" src=\"https:\/\/kedadhesive.com\/wp-content\/uploads\/2025\/02\/keda-marble-bonding-adhesive-application-1024x768.webp\" alt=\"Illustration of adhesive being spread along a prepared marble bonding face before edge assembly\" class=\"wp-image-1102\" srcset=\"https:\/\/kedadhesive.com\/wp-content\/uploads\/2025\/02\/keda-marble-bonding-adhesive-application-1024x768.webp 1024w, https:\/\/kedadhesive.com\/wp-content\/uploads\/2025\/02\/keda-marble-bonding-adhesive-application-300x225.webp 300w, https:\/\/kedadhesive.com\/wp-content\/uploads\/2025\/02\/keda-marble-bonding-adhesive-application-768x576.webp 768w, https:\/\/kedadhesive.com\/wp-content\/uploads\/2025\/02\/keda-marble-bonding-adhesive-application-16x12.webp 16w, https:\/\/kedadhesive.com\/wp-content\/uploads\/2025\/02\/keda-marble-bonding-adhesive-application-600x450.webp 600w, https:\/\/kedadhesive.com\/wp-content\/uploads\/2025\/02\/keda-marble-bonding-adhesive-application.webp 1448w\" sizes=\"(max-width: 1024px) 100vw, 1024px\" \/><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\">Protect adjacent finishes where appropriate. Test masking and cleanup materials on an offcut first so that residue, staining or surface damage does not become part of the repair.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Step 6: Position and Hold Without Distorting the Joint<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Bring the parts together in the rehearsed sequence and check alignment before the adhesive loses workability. Use padded fixtures suited to the geometry, distributing positioning force so the pieces remain in the intended plane.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Excessive force can move the strip, damage a delicate edge or squeeze away material needed at the interface. If tightening is being used to overcome poor fit, stop and reconsider the setup. The dry fit should already have established a workable geometry.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">Temporary Clamping and Permanent Support Have Different Roles<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Clamps hold the parts during curing. The finished stone assembly still needs the support required by its use, including the relevant countertop or installation arrangement.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Maintain support beneath the main piece and the added component. Check that a clamp is actually holding the intended parts and that its pads protect the visible surfaces.<\/p>\n\n\n\n<figure class=\"wp-block-image aligncenter size-large\"><img decoding=\"async\" width=\"1024\" height=\"768\" src=\"https:\/\/kedadhesive.com\/wp-content\/uploads\/2025\/02\/keda-marble-edge-lamination-clamping-1024x768.webp\" alt=\"Illustration of a supported marble edge-lamination sample held in alignment with padded clamps\" class=\"wp-image-1103\" srcset=\"https:\/\/kedadhesive.com\/wp-content\/uploads\/2025\/02\/keda-marble-edge-lamination-clamping-1024x768.webp 1024w, https:\/\/kedadhesive.com\/wp-content\/uploads\/2025\/02\/keda-marble-edge-lamination-clamping-300x225.webp 300w, https:\/\/kedadhesive.com\/wp-content\/uploads\/2025\/02\/keda-marble-edge-lamination-clamping-768x576.webp 768w, https:\/\/kedadhesive.com\/wp-content\/uploads\/2025\/02\/keda-marble-edge-lamination-clamping-16x12.webp 16w, https:\/\/kedadhesive.com\/wp-content\/uploads\/2025\/02\/keda-marble-edge-lamination-clamping-600x450.webp 600w, https:\/\/kedadhesive.com\/wp-content\/uploads\/2025\/02\/keda-marble-edge-lamination-clamping.webp 1448w\" sizes=\"(max-width: 1024px) 100vw, 1024px\" \/><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\">Remove excess adhesive using the product\u2019s cleanup method at the appropriate stage. Avoid smearing residue over porous stone or disturbing the joint while cleaning.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Step 7: Separate Handling, Finishing and Full Cure<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">A hard surface is only one observation. Removing fixtures, moving the piece, machining the edge and putting the assembly into service impose different demands.<\/p>\n\n\n\n<figure class=\"wp-block-table\"><table class=\"has-fixed-layout\"><thead><tr><th>Next operation<\/th><th>What to establish before proceeding<\/th><\/tr><\/thead><tbody><tr><td>Remove a positioning fixture<\/td><td>The joint can hold the intended position under the supported conditions<\/td><\/tr><tr><td>Move the assembly<\/td><td>Handling loads and the support arrangement fit the established cure stage<\/td><\/tr><tr><td>Grind or polish the edge<\/td><td>The adhesive withstands the actual tool, pressure and finishing process<\/td><\/tr><tr><td>Release for service<\/td><td>The required cure and installation checks are complete<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\">Establish these stages on a representative trial using the supplied product schedule. Record workshop and material conditions. When conditions change, revisit the affected stage instead of assuming the previous elapsed time still applies.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">The <a href=\"https:\/\/kedadhesive.com\/vi\/understanding-the-properties-of-marble-adhesive\/\" target=\"_blank\" rel=\"noreferrer noopener\">marble adhesive properties guide<\/a> explains these curing distinctions in more detail.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Step 8: Finish and Inspect the Whole Joint<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Use the finishing sequence appropriate to the stone and adhesive. Protect the corner, control tool pressure and heat, and check the joint after the intended final finish. Where wet processing is planned, include it in the product and process review.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Inspect from a normal viewing position and an oblique angle. Look for lippage, open sections, pinholes, a recessed adhesive line, chips, color mismatch, halos and differences in sheen.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Smearing or adhesive pull-out during a trial is a reason to stop and investigate cure or the interface. Continuing with a finer abrasive can leave the underlying defect unresolved.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Common Marble-Bonding Problems and First Checks<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">These are starting points for investigation, not proof of a single cause.<\/p>\n\n\n\n<figure class=\"wp-block-table\"><table class=\"has-fixed-layout\"><thead><tr><th>Problem<\/th><th>Possible contributors<\/th><th>First useful check<\/th><\/tr><\/thead><tbody><tr><td>Joint remains open at one end<\/td><td>Poor cut, rocking face, debris or fixture distortion<\/td><td>Repeat the dry fit on supported parts and inspect the contact faces<\/td><\/tr><tr><td>Edge strip moves during positioning<\/td><td>Slippery uncured interface or an unstable fixture arrangement<\/td><td>Rehearse supported positioning and verify clamp access on a trial<\/td><\/tr><tr><td>Visible surfaces sit at different levels<\/td><td>Uneven support, piece thickness or alignment changes<\/td><td>Check the dry fit, pads and support plane<\/td><\/tr><tr><td>Adhesive line smears or pulls out<\/td><td>Early machining, incomplete cure or a weak interface<\/td><td>Compare the mixing record, cure conditions and separated surfaces<\/td><\/tr><tr><td>Joint has a dark border<\/td><td>Staining, contamination, moisture or stone sensitivity<\/td><td>Investigate the actual materials on an offcut before visible production<\/td><\/tr><tr><td>Failure exposes weak stone or an old coating<\/td><td>The joint depends on an unsound surface layer<\/td><td>Assess the substrate or treatment and revise preparation or selection<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n<h2 class=\"wp-block-heading\">Keep a Short Production Record<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Retain the sample and record the stone batch, joint geometry, adhesive and hardener identities, color recipe, measured quantities, material temperature, assembly sequence and finishing schedule.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Include photographs before mixing and after finishing. Note the fixture arrangement and the appearance accepted. Recheck relevant details when the stone treatment, adhesive grade or machining process changes.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Selecting a KEDA Product for the Job<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\"><a href=\"https:\/\/kedadhesive.com\/vi\/product\/knife-grade-polyester-marble-adhesive\/\" target=\"_blank\" rel=\"noreferrer noopener\">KEDA Knife Grade Polyester Marble Adhesive<\/a> is the associated product for suitable nonstructural stone-fabrication and local-repair inquiries.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Send a photograph of both bonding faces, the proposed joint, the intended finish and service conditions. For supply planning, add the destination market, preferred color, pack size and quantity. These details make the inquiry specific enough to review the product and process together.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Conclusion<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">A repeatable marble-to-marble bond starts with fit and a sound interface, then carries that preparation through mixing, positioning, curing and finishing. Use a representative sample and a recorded process to connect the adhesive choice to the finished result.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Frequently Asked Questions<\/h2>\n\n\n\n<h3 class=\"wp-block-heading\">1. Should polished marble bonding faces be roughened?<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Use the preparation method specified for the actual product and surface. Where abrasion is required, confine it to the bonding area, protect the visible finish and remove preparation dust. Treated or resin-backed stone needs its own interface assessment.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">2. Can I fill a poor-fitting joint with extra adhesive?<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">First correct cut accuracy, debris, rocking or alignment where practical. An adhesive has its own permitted joint geometry; extra material does not establish a sound repair for an arbitrary gap. Reproduce the proposed joint in a trial.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">3. How tightly should I clamp the marble?<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Use the positioning force and fixtures appropriate to the assembly and adhesive. Keep the parts aligned and preserve the intended bond line. There is no universal pressure value for every stone thickness, joint and product.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">4. When can I remove clamps and polish the edge?<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Assess those operations separately against the product schedule and a supported trial. Handling readiness does not automatically establish machining readiness. Record temperature and conditions rather than relying on a generic number of minutes.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">5. Can this method repair a load-bearing marble component?<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">This guide concerns nonstructural workshop fabrication and local repair. A load-bearing component, overhang or installed panel needs an assessed connection and support system. A successful decorative-edge trial cannot establish that design.<\/p>\n\n\n\n<hr class=\"wp-block-separator has-alpha-channel-opacity\"\/>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Planning a marble edge or local repair?<\/strong> <a href=\"https:\/\/kedadhesive.com\/vi\/contact\/\" target=\"_blank\" rel=\"noreferrer noopener\">Discuss the joint with KEDA<\/a> using photographs, stone details and your processing requirements so the adhesive selection can start with the actual work.<\/p>","protected":false},"excerpt":{"rendered":"<p>Build a repeatable marble-to-marble bonding process for decorative edges and local repairs. Follow dry fitting, surface preparation, color approval, mixing, positioning, curing and final inspection.<\/p>","protected":false},"author":1,"featured_media":1104,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"_acf_changed":false,"page_builder":"","footnotes":""},"categories":[84],"tags":[92,85,91,82],"class_list":["post-402","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-marble-stone-adhesives","tag-edge-lamination","tag-marble-adhesives","tag-marble-bonding","tag-stone-fabrication"],"acf":[],"_links":{"self":[{"href":"https:\/\/kedadhesive.com\/vi\/wp-json\/wp\/v2\/posts\/402","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/kedadhesive.com\/vi\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/kedadhesive.com\/vi\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/kedadhesive.com\/vi\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/kedadhesive.com\/vi\/wp-json\/wp\/v2\/comments?post=402"}],"version-history":[{"count":2,"href":"https:\/\/kedadhesive.com\/vi\/wp-json\/wp\/v2\/posts\/402\/revisions"}],"predecessor-version":[{"id":1105,"href":"https:\/\/kedadhesive.com\/vi\/wp-json\/wp\/v2\/posts\/402\/revisions\/1105"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/kedadhesive.com\/vi\/wp-json\/wp\/v2\/media\/1104"}],"wp:attachment":[{"href":"https:\/\/kedadhesive.com\/vi\/wp-json\/wp\/v2\/media?parent=402"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/kedadhesive.com\/vi\/wp-json\/wp\/v2\/categories?post=402"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/kedadhesive.com\/vi\/wp-json\/wp\/v2\/tags?post=402"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}