Two-component epoxy
Matched Part A and Part B for professional bonding enquiries.
For stone cladding & prepared bonding interfaces
Two-component epoxy adhesive for professional stone-cladding and bonding enquiries. Select the grade for the stone, support material and specified installation system. Supplied as separate Part A and Part B components.
Measure equal volumes of Part A and Part B.
Typical component colours. Pure white option available.
For overseas distributors, stone installers & contractors.
Matched Part A and Part B for professional bonding enquiries.
Measure equal volumes of the two components.
Keep each component in its own container until mixing.
Match the grade to the stone, support and fixing system.
| Adhesive family | Two-component epoxy adhesive |
|---|---|
| Components | Part A and matched Part B |
| A:B mixing ratio | 1:1 by volume |
| Measurement basis | Equal volumes; not an assumed 1:1 weight ratio |
| Typical component colours | Part A: Beige / Part B: Grey |
| Additional colour option | Pure white version available |
| Pack format | Separate Part A and Part B containers |
| Application focus | Stone-cladding interfaces and project-specified rigid bonding |
Confirm the supplied grade, working time, curing schedule and required order capacity with KEDA. Installation design determines bonding areas and mechanical supports.
Discuss adhesive at prepared stone and metal bracket interfaces within the specified cladding assembly.
Review stone-to-stone joints and rigid stone details with the actual bonding faces and joint geometry.
Discuss sound, cured concrete and other specified mineral substrates after compatibility assessment.
Share the stone type and backing, metal finish or mineral substrate, plus the fixing arrangement. Check adhesion on the actual materials and surface treatments. Give particular attention to coated metal, sealed stone and resin- or mesh-backed panels.
Measure the components by volume, then mix thoroughly until uniform. Colour uniformity alone may not confirm complete mixing.
Component colours are indicative. A pure white version is available; confirm its component appearance separately.
Pack volume does not establish component weight. Do not convert a volume ratio into a weight ratio without confirmed instructions.
Start here for stone-to-support bonding and project-specified rigid interfaces. Share the actual stone, support, joint and fixing arrangement.
A:B = 1:1 by volumeReview the white slab adhesive for indoor ceramic large-format slabs and sintered-stone panel installation.
Confirm the slab backing, substrate, dimensions and installation area. Select its mixing and application instructions separately.
Explore Interior Slab AdhesivePrepare sound, clean, dry bonding faces. Remove dust, oil, rust and loose material; assess coatings and surface treatments on the actual assembly.
Measure Part A and Part B in equal volumes. Use separate clean tools to take the components, then mix thoroughly in a separate clean container, scraping the sides and bottom. Prepare a batch matched to the installation pace.
Place adhesive at the project-specified bonding interfaces, contact area and thickness. Position the parts and retain the required mechanical supports and fixings.
Keep the assembly supported and undisturbed during curing. Follow the supplied grade-specific instructions and project requirements before removing supports or applying loads. Surface hardness alone does not confirm readiness for service.
Use the matched A/B components. Do not add extra Part B, water, solvent or unapproved additives. Obtain product-specific safety information for both components.
The confirmed A:B ratio is 1:1 by volume. Measure equal volumes of Part A and Part B. Do not assume equal weights give the same ratio; use a weight-based instruction only if KEDA confirms it for the actual supplied grade.
Part A is typically beige and Part B grey. A pure white option is also available. Confirm the required version and component appearance against actual samples.
The gallery packaging shown is 10 L Part A + 10 L Part B. Tell us your required capacity and estimated order quantity to confirm the available supply configuration.
No automatic substitution is implied. Bonding areas, brackets, anchors and supports follow the project design and specified installation system.
Review Low-Odor Epoxy Slab Adhesive, available in white, for indoor ceramic large-format slab and sintered-stone installation enquiries. Confirm the slab backing, substrate and installation requirements separately.
Samples can be provided free of charge, with freight paid by the customer. This core product uses the KEDA brand. English packaging, selection guidance and technical information can be discussed with your order.
Share your stone, support material, fixing arrangement, destination market and estimated order quantity. Discuss the suitable grade and supply configuration with KEDA.
KEDA 2-Component Epoxy Structural Adhesive